Everyone will have their own individual theory about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Mounting a bath tub isn't specifically brain surgery, however it does need solid plumbing, woodworking, and often, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably tough task. If the old tub is readily available, the job can move rapidly; if you need to open up a wall to get rid of the old tub and position the new bathtub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will require an assistant to leave the old bathtub as well as embeded in the new one. Ensure you have qualified on your own for the task and also are comfortable attempting it. As opposed to working with a service provider to take over a halfway-completed task, it is far better to take into consideration utilizing one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This article will certainly assist you set up a new bath tub in your restroom if you have already acquired a brand-new bathtub as well as do not need to transform the setup of your previous water pipelines.
Your tools and material list should consist of the following:
Getting ready for the Setup
To start with, the sustaining structure provided with the bath needs to be fitted (if required) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to ensure that if the tap features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets unit to stop pressure on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to now prepare to be suited its last setting.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you ought to do is disconnect the supply of water. After doing so, turn on the taps to drain any water continuing to be in the system. The process of eliminating the existing taps can be quite bothersome because of the limited accessibility that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have been gotten rid of, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bath tub
Utilizing both wood boards under its feet, position the tub in the needed setting. The wood boards are helpful in evenly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four tiny factors.
The following goal is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the tub till the level reviews degree.
To mount taps, fit the bottom of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression join; then do the exact same for the other faucet.
Switch on the water supply and check all joints and brand-new pipework for leakages and also tighten them if needed. Load the bathtub and additionally examine the overflow electrical outlet as well as the regular electrical outlet for leakages.
Lastly, repair the bathroom paneling as defined in the producer's instruction manual. Tiling as well as securing around the bath tub must wait up until the bath tub has been used at the very least once as this will certainly resolve it into its final setting.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to avoid damage to the thread. One end of the port fits on the plastic tail of the tap and also the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making certain that the washers remain in place between the faucet and the sink. Safeguard the faucet in place with the supplier offered backnut. As soon as the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The previous type should be connected to the faucet finishes initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to split a rigid seal, triggering the water to permeate the wall in between the bathroom and the tiling, leading to problems with wetness and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can split rather early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise quickly offered on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about A Step-by-Step Guide to Installing a Bathtub? Try to leave feedback directly below. We will be pleased to see your ideas about this blog posting. In hopes that you come back again soon. If you enjoyed reading our blog posting kindly be sure to pass it around. We enjoy reading our article about Installing A Bathtub.
For true quality, dial!